4000W 100A MPPT Solar Charge Controller Battery PV Regulator USB

You Also Like USD 20.49 50kg Max Alloy Rear Bicycle Pannier Rack Carrier Bag Luggage Cycle Mountain Bike BUY NOW USD 20.95 40W Socket Fan Light with Remote,Portable Small Ceiling Fans with Lights Bulb BUY NOW USD 31.59 12X Large 12LED Solar Power Torch Light Flickering Flame Garden Waterproof Lamp BUY NOW USD 11.99 99000LM CSP LED Headlamp Rechargeable Head Light Flashlight Torch Lamp Camping BUY NOW USD 17.99 Cordless 150 PSI Air Compressor Tire Inflator Fits Car Moto Bike Tires Air Pump BUY NOW USD 19.09 12Pack Solar Pathway Lights Outdoor Landscape Solar Waterproof Garden LED Lights BUY NOW USD 19.99 Brushed Nickel Kitchen Faucet Sink Mixer Faucet Pull Down Sprayer Single Handle BUY NOW USD 19.39 50pcs 39.37" Electric Connecting Wire for Fireworks Firing System Igniter Xmas BUY NOW USD 12.95 Bluetooth RGB LED Beanie Hat with Music Speakers Mic Rechargeable Cap Head Lamp BUY NOW USD 12.99 Solar Power 122 LED Light 3 Heads Motion Sensor Outdoor Garden Yard Flood Lamp BUY NOW USD 20.79 2 Pack LED Motion Sensor Solar Lights ,Outdoor IP65 Waterproof Security Lamp BUY NOW USD 8.95 Outdoor Solar String Lights LED Bulbs For Patio Backyard Yard Gazebo Porch Party BUY NOW Feature: LCD Liquid Crystal Display: Large LCD display, support battery working status display, solar panel working status display, mode control display, load output status and each parameter display, normal and fault status display. 7 Operation Modes：Charging mode, light control mode, light control + time delay control mode, general control mode, manual control mode, timing control mode and test mode, the test mode is only for factory test use. 4 kinds of voltages automatic identification：It will automatic identify DC12V/24V, DC36V, DC48V by itself. Large-section Wiring Port: use large-section, large-spacing wiring ports, can be installed 16mm wire, the wire spacing of 7mm increases the insulation performance and the reliability of installation, effectively reduces current and voltage drop while reducing losses. Dual USB Charging Ports: The solar charge controller adopts a dual USB charging port design, which can charge two devices at the same time, and supports most of USB port devices, such as mobile phones, tablets, PSP game consoles, etc. Thickened Aluminum Alloy Heat Sink: The MOS tube is used to lock the heat sink design, the heat dissipation is more uniform, and there is no fear of the temperature rise caused by the MOS tube, the powerful heat dissipation capacity can operate normally in the environment of 55 ℃, at the same time, it is equipped with functions to prevent overcharge, overvoltage, DC output low voltage, high voltage protection and reverse polarity protection, etc. Clock setting instructions: When the battery is connected, press "▲" "▼" to set the clock table, short press "■" to save. Charging voltage setting instructions: After connecting the battery, after setting the clock and saving, long press "▲" for 3-5 seconds, the screen displays L**V as the floating charge voltage, which can be adjusted by pressing "▼"; short press again "▲"H**V is to increase the charging voltage, which can be adjusted by pressing "▼"; shortly press "▲" again. F**V is the low-voltage cut-off voltage of the DC load, which can be adjusted by pressing "▼"; after setting Long press "▲" for 3-5 seconds to save and exit. Specification: Type: Solar Charge Controller Maximum charging current: 100A Maximum input voltage of photovoltaic panels: 15V-23V(12V), 30V-45V(24V), 45V-69V(36V), 60V-90V(48V) Maximum input power of photovoltaic panels: 1000W (12V), 2000W (24V), 3000W (36V), 4000W (48V) Output voltage: DC12V/24V/36V/48V; DC5V/1.5Ax2USB Support Battery: Lithium Battery & Lead Acid Battery Working temperature: -25℃~55℃ Cooling method: heat sink self-cooling Charging method: Focused MPPT modulation charging Working mode: seven Protection function: prevent overcharge, overvoltage/DC output low voltage, high voltage protection, reverse polarity protection, etc. Package list: 1 × Solar Charge Controller 1 × Manual Note: 1.Please connect the battery to the controller first, and then the photovoltaic panel to ensure that the battery voltage is higher than (12V battery is higher than 10V; 24V battery is higher than 20V; 36V battery is higher than 30V; 48V battery is higher than 40V), otherwise it will cause voltage Identification error. 2. It is high quality compatible MPPT + PWM Solar Controllers ,not 100% Ture MPPT