Honda Acura 20mm Wheel Spacers 5x114.3 Hubcentric 64.1mm (2pcs)

[Important Notes] 1. Check Your Vehicle Bolt Pattern/ PCD, Hub Bore Size, Thread Pitch, Vehicle fitment compatibility is only a guide. 2. Measure the fender gap and stock bolt length to choose suitable thickness. 3. PLEASE CONFIRM what you actuall need, wheel spacers or wheel adapters, they are different. Wheel Adapters are used to change bolt patterns in order to properly fit wheels from one vehicle to the hub of a different vehicle. 4. Do not use impact wrench.Please use hand wrench. Recommended to use threadlocker. 5. Returns are only accepted if unused and not installed.(ReturnsARE NOT ACCEPTED IF SPACERS-ADAPTERS HAVE BEEN INSTALLED TO YOUR VEHICLE) Wheel Bolt Pattern 5x4.5 (5x114.3) Vehicle Bolt Pattern 5x4.5 (5x114.3) Thickness 20MM per spacer Thread Pitch 12X1.5 Quantity 2pcs per set Hub/Center Bore 64.1mm Studs 10.9 Grade, stronger than OEM 8.8 Grade

Material 6061 T6 Billet Aerospace Aluminum Surface Treatment Anodized For 1998-2022 Honda Accord For 2006-2022 Honda Civic For 1997-2022 Honda CR-V For 2011-2016 Honda CR-Z For 2012-2015 Honda Crosstour For 2003-2011 Honda Element For 2016-2022 Honda HR-V For 2019-2022 Honda Insight For 1995-2004 Honda Odyssey For 2003-2008 Honda Pilot For 19997-2001 Honda Prelude For 2000-2009 Honda S2000 For 2001-2003 Acura CL For 2006-2011 Acura CSX For 2013-2021 Acura ILX For 2001-2016 Acura MDX For 2007-2022 Acura RDX For 1997-2004 Acura RL For 2002-2006 Acura RSX For 1996-2008 Acura TL For 2015-2020 Acura TLX For 2004-2014 Acura TSX Bolt pattern conversion adapter (Lug centric) This spacer set includes open end lug nuts to secure the spacers onto your factory hubs Your Factory wheel studs may extend past the surface of the wheel spacers. In this case you will need to: 1.Shorten the factory studs 2.The wheels need to have the open slots (cavities) between mounting holes. 3.Purchase a set of shorter studs and replace them with the factory studs. [Important Notes] 1. Check Your Vehicle Bolt Pattern/ PCD, Hub Bore Size, Thread Pitch, Vehicle fitment compatibility is only a guide. 2. Measure the fender gap and stock bolt length to choose suitable thickness. 3. PLEASE CONFIRM what you actuall need, wheel spacers or wheel adapters, they are different. Wheel Adapters are used to change bolt patterns in order to properly fit wheels from one vehicle to the hub of a different vehicle. 4. Do not use impact wrench.Please use hand wrench. Recommended to use threadlocker. 5. Returns are only accepted if unused and not installed.(ReturnsARE NOT ACCEPTED IF SPACERS-ADAPTERS HAVE BEEN INSTALLED TO YOUR VEHICLE) -- Vehicle fitment compatibility is only a guide, please ensure that these are the correct ones for your vehicle. -- For 1 inch or less or special adapters, If your vehicle requires 2" spacers but you purchased ≤1" , the stock studs are longer than the adapters, and the wheels do not have hollow spot in them, you may need to grind, or cut your existing lugs if you don't choose to purchase shorter studs. -- For 2 inches or more or special adapters, If your vehicle requires 1" spacers but you purchased ≥2", the stock studs are shorter to hold the spacer safely, you need to exchange to small

size adapters or purchase longer studs yourself. What should I pay attention to during installation? 1) Check to make sure that the wheel spacer fits perfectly with the hub/axle stub and the inner mounting surface of the wheel. 2) Make sure that the wheel bolts being used are of the appropriate length, not too long or too short. 3) DO NOT proceed if both of the wheel spacer do not fit. 4) Please be sure to clean the rust on the hub before starting the installation, otherwise it will affect the working life of the spacers. 5) Make sure that you get 5-7 FULL TURNS of the lugs when installing. Torque them down to the manufacturers specs (up to and not greater than 110ft lbs). 6) Avoid using an impact wrench because improper usage may cause the lug nuts/bolts to break or loosen while driving causing a potential injury or accident.7) All lug nuts, bolts and torque must be checked after driving the first 50 miles after installation. Afterwards, please check all lug nuts and bolts every 3,000-5,000 miles. 8) Alignment is necessary after installation, this will prevent any wobble and vibration from occurring.